Skip to content
Call (828) 470-1105Licensed, bonded & insured

Countertop Refinishing & Resurfacing in Asheville, NC

Countertop refinishing & resurfacing in Asheville, NC renews stone that is still sound but dull, etched or scratched. Buncombe Custom Countertops honors what is worth keeping, restores it, and tells you plainly when replacing the top makes more sense.

  • Free in-home measure
  • Slab approved before any cut
  • Licensed, bonded & insured

Get a free countertop estimate

Restore it or replace it

Refinishing works when the stone is solid and the surface has simply worn. Dull patches, etch marks and fine scratches come out with honing and polishing, and a fresh sealer finishes the job. If a top is cracked, loose or the wrong material for your family, replacement is the better choice, and we will say so at the first visit.

Serving Asheville, Candler and Arden, we look at the top in your kitchen, test it, and explain what can and cannot be brought back. You get a written quote after the free in-home measure, and the choice between restoring and replacing stays yours.

Why Buncombe Custom Countertops

How an assessment works

We test the surface before we promise anything.

Stone identifiedWe confirm what the top is made of, since each material is treated differently
Damage mappedEtching, scratches and stains are marked and sorted by how deep they go
Options comparedRefinish, repair or replace, with what each one costs and delivers
Honest adviceIf replacement is the better value, you hear it before any work starts

Refinishing, resurfacing and replacing compared

These three words get used loosely, and the difference matters for your money. Refinishing works on the existing stone itself, by grinding away a thin layer of surface and re-polishing it. Resurfacing puts a new layer over an old top, which is what people usually mean for laminate or worn tops they want to keep in place. Replacement removes the old top and installs a new one. Which is right depends on the material, the damage and what you want the kitchen to look like afterward. Here is how we sort them:

Refinishing natural stone

Granite, marble and quartzite can be honed or polished in place. It is the lightest touch, and usually the first thing to try on sound stone that has lost its finish.

Resurfacing a dated top

A coating system over laminate or a tired surface changes color without a demolition. It is a limited, lower-cost update, and its durability is not that of stone, so we explain the tradeoffs first.

Repairing isolated damage

A chip, crack or burn mark may be fixed locally with filler or an inlay, rather than treating the whole top. The result depends on color and stone.

Replacing the top

When the stone is cracked through, badly stained or no longer what you want, a new top is the cleaner path. Because the cabinets stay, the change is smaller than a full remodel.

When the cabinets decide

A top is only as good as what carries it. If the boxes are failing, replacing the top alone will not help, and we say so. We check that the cabinets are level and the countertop is firmly supported before recommending any work, since a restored finish will not last on a surface that flexes or shifts.

What refinishing can and cannot fix

Etching is the most common complaint on marble and some other soft stones. An acidic spill, such as citrus juice or wine, dulls the polished face by dissolving a tiny layer of calcite. The mark is not a stain. It is a change in the surface, and honing the area level and re-polishing it removes it. Fine scratches and the hazy dullness of a worn finish come out the same way.

There are limits. Deep gouges, cracks that run through the stone and stains that have soaked in below the surface may need a repair instead. Engineered quartz is a resin and stone composite, so it is not honed the way natural stone is, though light marks may be buffed. We test a small area first and explain what we can promise before going further.

Navy shaker cabinets with white quartz counters and a waterfall-edge quartz island, a stainless hood, glass pendants, wood bar stools and black-framed windows onto green wooded hills

Choosing your finish: polished, honed or satin

Refinishing is also a chance to change how the stone looks, not just restore what you had. The finish on a countertop is a matter of how smooth the abrasives left it, and it can be taken in either direction. Many people discover they prefer a softer look once they see it in their own kitchen.

High-gloss polish

A mirror finish brings out deep color and bold veining. It shows water spots and etching more readily, so it asks for a little more care.

Satin and honed finishes

A honed surface has a soft, low sheen that hides fingerprints and small marks. It is a popular way to update a dated glossy kitchen without replacing the stone.

Changing the finish

A polished top can be honed to a matte look, and a honed one can be polished up. We show you a test patch before treating the whole surface.

Sealing after finishing

Honed and polished stone both need a sealer afterward, since opening the surface also opens its pores. We seal as the last step of every refinishing job.

Dull granite, hard-water film and failed sealer

Granite rarely loses its polish from wear alone. More often a film of soap residue and mineral deposits from hard water builds up on the surface and makes it look cloudy. Cleaning with a stone-safe product may bring much of the shine back, and a mechanical polish with fine diamond pads finishes the job when the film is not the whole story.

Failed sealer is a different problem, and it looks different too:

  • Water soaks in and darkens the stone instead of beading up.
  • Oily marks near the cooktop stay for days.
  • Dark rings appear under glasses and bottles.

In those cases the cure is to clean the surface properly, let it dry and apply a fresh penetrating sealer. That is a quicker, cheaper job than a full refinish, and we will tell you which one your counters need.

Kitchen peninsula in warm Calacatta gold marble with rich gold and grey veining, two leather bar stools in the foreground, cream cabinets and brass hardware in a 1920s bungalow kitchen

What refinishing and resurfacing cost in Asheville

Refinishing is usually far less than replacing a countertop, though the figure depends on the size and condition of the surface. A hone and polish refresh is commonly estimated at roughly $8 to $20 per square foot, and a full kitchen takes longer than a small area. Etch and stain restoration on a limited area is typically estimated at roughly $200 to $600. A resealing visit alone is estimated at roughly $150 to $400.

The factors that change the number:

  • How much surface needs work and how many separate areas.
  • The material, since marble, granite and quartzite all behave differently.
  • How deep the damage goes: surface etching versus gouges.
  • Whether the finish is being changed, such as polished to honed.
  • Access to the room and the amount of masking needed around cabinets.

Every figure above is an estimate that can shift with the condition we find, and the number to trust is the one in your written quote.

Refinishing for rentals and light commercial spaces

Rental owners, property managers and small offices often have sound stone that has simply taken a beating. A refresh between tenants can update a kitchen at a fraction of replacement cost. Call with the number of units or rooms, and we can look at several at once and quote them together. A common approach is to start with one unit as a pilot, check the result in person, and then schedule the rest in batches so no apartment sits empty longer than it has to. We also keep notes on what each surface needed, so the next turnover goes faster.

Same Cabinets, New Countertops

Drag the handle. The cabinets stayed; only the top changed.

Kitchen with honey oak cabinets, beige laminate counters, a white electric range and dishwasher, and a double stainless sink under a window onto blue mountain ridgesThe same kitchen and oak cabinets with charcoal stone counters and a matching backsplash, an undermount stainless sink and the same window onto the ridgesBeforeAfter
Laminate to stone, cabinets kept
Bathroom vanity with an oak base, a beige cultured marble top with an integrated basin, a brushed nickel faucet and a wide mirrorThe same oak vanity with a white quartz top in soft grey veining, a rectangular undermount basin and a widespread brushed nickel faucetBeforeAfter
Cultured marble to quartz with an undermount basin

The process

How a Countertop Job Runs

  1. The assessment

    We look at the surface, identify the stone, and test a small area so we know what can be restored.

  2. The written quote

    You get the scope, the finish you chose and the price in writing. Nothing starts until you approve it.

  3. Hone, polish and seal

    We level etching and scratches, bring the finish to the sheen you picked, and apply a fresh sealer.

  4. Walk-through and care

    We go over the finished surface with you and explain the simple upkeep that keeps it looking new.

Questions

Refinishing and Resurfacing: Common Questions

Is refinishing cheaper than replacing my countertops?

Almost always, when the stone is sound. Refinishing skips demolition, new slabs and a template, so the cost is a fraction of a new top. If the top is cracked or failing, replacement is the better use of money, and we will tell you.

Can etch marks on marble be removed?

Yes, in most cases. Etching is damage to the polished surface, not a stain, so honing the area level and re-polishing it removes it. Very deep etching may need more passes, and we test a small patch before we promise anything.

Can you make my dull granite shiny again?

Usually. Cloudiness often comes from a film of soap and mineral deposits, which we clean off first. If the polish itself has worn, we re-polish with fine diamond pads, then seal the stone.

Can a polished top be changed to matte?

Yes. Honing smooths the surface to a satin or matte look, and the process can run the other way. We show a test patch so you can judge the result in your own light before we do the whole kitchen.

Does quartz need refinishing?

Rarely. Quartz is engineered and resists staining, so it seldom needs the treatments natural stone does. Minor surface marks can sometimes be buffed out, and deeper damage is a repair or replacement question.

Can laminate counters be resurfaced?

Sometimes, with a coating system, though it will not match the durability of stone. We look at the condition first. For a lasting update, many homeowners find that replacing laminate with stone is the better long-term choice.

How long does a refinish take?

A reseal alone is over quickly. Doing a whole kitchen from start to finish usually takes a working day or longer, depending on the square footage. We set the schedule at the measure and put it on the quote, so you know when the kitchen is back.

How long should I wait before using the counters?

Light use is usually fine within hours, but sealers need longer to cure fully. We give you exact timing based on the product used on your stone, and we recommend keeping spills off for the first day or two.

Free in-home measure

Talk to us about restoring your countertops

Free measures across Buncombe County. Builders, cabinet shops and property owners can send drawings for a bid.

Call (828) 470-1105

Licensed, bonded & insured. Calls only, we do not receive text messages.

Call (828) 470-1105Licensed, bonded & insured